Can you put a used Huawei UBBP or UMPT board from an older site into a Huawei BBU5900? Often yes, but not always. The BBU3900, BBU3910 and BBU5900 share the same 19-inch, 2U form factor and the same board families, yet each chassis uses its own power and fan modules, and the newer g-series boards are aimed at the BBU5900 (and partly the BBU3910). Whether a board actually works also depends on the software release and licenses on the site. This guide explains which parts are interchangeable and what to check before you order.
The three Huawei BBU platforms at a glance
All three units belong to Huawei’s distributed base station family (DBS3900 / DBS5900). The baseband unit hosts a main control and transmission board (UMPT), one or more baseband processing boards (UBBP), plus power, fan and optional environment monitoring and satellite clock boards. Remote radio units connect to the UBBP over CPRI fibre.
| Item | BBU3900 | BBU3910 | BBU5900 |
|---|---|---|---|
| Chassis | 19-inch, 2U | 19-inch, 2U | 19-inch, 2U, 86 x 442 x 310 mm |
| Power module | UPEUa / UPEUc | UPEUd | UPEUe |
| Fan module | FAN / FANc | FANd | FANf (2100 W heat dissipation) |
| Backplane between baseband slots 0–5 | Slots 0, 1, 4 and 5 exchange data through slot 2 or 3 | Direct data exchange between slots 0–5 | Half-width slots 0–5; adjacent pairs can be combined into a full-width slot |
| Legacy WBBP / LBBP boards | Supported | Not used | Not used |
| 5G NR | No | Not the target platform | Yes, Huawei’s 5G-ready BBU |
The practical point: power and fan modules are not interchangeable between generations. A UPEUe and FANf belong to the BBU5900; a BBU3910 needs a UPEUd and FANd. When buying a used chassis, ask whether it comes with the correct power and fan units already fitted.
Slot layout on the BBU5900
Huawei’s BBU5900 hardware documentation defines a fixed slot plan:
- Slots 0–5: half-width service slots for UBBP baseband boards (and the satellite card). Two horizontally adjacent half-width slots can be combined into one full-width slot.
- Slots 6 and 7: UMPT main control boards, up to two, with slot 7 used first.
- Slot 16: FANf fan module.
- Slots 18 and 19: UPEUe power modules (slot 19 first). Slot 18 can alternatively hold the UEIUb environment monitoring unit.
For LTE baseband boards in the BBU5900, the documented installation priority is slot 4, then 2, 0, 1, 3 and 5. Follow this order when adding capacity so the configuration matches what the OSS and commissioning scripts expect.
Which UMPT boards fit which BBU
The UMPT (Universal Main Processing and Transmission unit) handles control, transport and clock for the whole base station. Huawei’s DBS5900 product page lists UMPTe2, UMPTe3, UMPTg2 and UMPTg3 as main control boards for the BBU5900.
- UMPTe series (for example the Huawei UMPTe3) is used in both the BBU3910 and the BBU5900, which makes it a flexible spare for operators running mixed fleets.
- UMPTg series (UMPTg3, UMPTg5) is a newer generation intended for the BBU5900.
- Older UMPTa / UMPTb boards and the LTE-only LMPT belong to BBU3900-era sites. Do not plan a BBU5900 deployment around them.
Which UBBP boards fit which BBU
UBBP (Universal Baseband Processing) boards provide the CPRI ports to the radio units and process the uplink and downlink baseband signals. Huawei’s BBU5900 product page lists UBBPe4, UBBPg1a and UBBPg2 as baseband boards for that chassis. The table below summarises how the boards we commonly supply are typically used:
| Board | Series | Typical host BBU | Notes |
|---|---|---|---|
| UBBPe4 | e-series | BBU3900, BBU3910, BBU5900 | Widely used LTE-era board; listed by Huawei for BBU5900 |
| UBBPe6 | e-series | BBU3900, BBU3910, BBU5900 | Higher-capacity e-series board |
| UBBPg1 / UBBPg2a | g-series | BBU3910, BBU5900 | 4G/5G-generation boards |
| UBBPg1a / UBBPg2 / UBBPg3 | g-series | BBU5900 | UBBPg1a and UBBPg2 listed by Huawei for BBU5900 |
Two rules of thumb follow from this. First, e-series boards such as the Huawei UBBPe4 are the most portable option when you maintain BBU3900, BBU3910 and BBU5900 sites side by side. Second, g-series boards should be bought for BBU5900 sites (and selected BBU3910 cases), not as spares for an old BBU3900.
Software, licences and mode: the hidden compatibility layer
A board that physically fits a slot is not guaranteed to work in service. Before installing a used board, confirm:
- Software release. Each UBBP and UMPT variant is supported from a specific SRAN / eRAN version onward. Huawei documentation, for example, notes that certain UBBPe variants are only available from a given eRAN release. If the site runs an older load, the board may not be recognised.
- Radio access technology. Check that the board supports the mode you need (GSM, UMTS, LTE FDD/TDD, NR) on that software release, and that the UMPT can control the same mode combination.
- Licences. Capacity and features are licence-controlled on the site, not stored on the board. Replacing a board does not transfer licences, and adding a board does not add capacity without the matching licence.
- CPRI topology. Match the CPRI rate and port count to the radio units on site, and keep the existing fibre mapping when swapping a like-for-like board.
- Power and cooling budget. Adding several high-capacity boards to a chassis increases heat load. The BBU5900’s FANf is rated for 2100 W of heat dissipation; older chassis with older fan modules have lower limits.
Upgrading from BBU3900/BBU3910 to BBU5900
Many operators replace BBU3900 or BBU3910 units with BBU5900 when adding LTE capacity or preparing for 5G NR. A typical used-equipment upgrade looks like this:
- Fit a BBU5900 chassis with UPEUe power and FANf fan modules.
- Reuse UMPTe and UBBPe boards from the old site where the target software release supports them, or move to UMPTg / UBBPg boards for higher capacity.
- Keep the existing RRUs if they are supported on the new release; the CPRI interface stays the same type.
- Re-export and adapt the site configuration in the OSS, then re-apply licences to the new equipment.
Because the chassis dimensions are the same 19-inch, 2U format, the BBU5900 normally fits the same cabinet space, which keeps civil work to a minimum.
What to check when buying used Huawei boards
- Read the exact board name and BOM code on the label and compare it with your site inventory. Similar names (UBBPg1 vs UBBPg1a, UBBPg2 vs UBBPg2a) are different boards.
- Inspect connectors, SFP cages and the backplane connector for bent pins or corrosion.
- Ask for a power-on test in a matching BBU with board status and alarm check.
- Confirm the board is supported by your current software load before ordering in volume.
FAQ
Can I use a BBU3910 power module in a BBU5900?
No. The BBU3910 uses the UPEUd power module and FANd fan, while the BBU5900 uses the UPEUe and FANf. Order the modules that match the chassis.
Does a UBBPe4 work in the BBU5900?
Yes. Huawei lists the UBBPe4 among the baseband boards for the BBU5900, and it is also used in BBU3900 and BBU3910 sites, subject to the software release on site.
Can I put UBBPg boards in a BBU3900?
Plan g-series boards for BBU5900 (and, for some variants, BBU3910) sites. For BBU3900 spares, e-series and earlier boards are the safer choice.
Do licences move with the board?
No. Capacity and feature licences are managed per base station. After a swap or upgrade, make sure the site licence covers the new configuration.
Source tested Huawei BBU boards from Haokang
We supply used and refurbished Huawei BBU5900, BBU3910 and BBU3900 units, UMPT and UBBP boards, and Huawei RRUs. Browse the full range in our Huawei category. All units are tested before shipment and come with a 90-day warranty, and we ship worldwide in secure packaging. Contact us on WhatsApp at +86 187 3329 4669 or +86 139 3088 8705, email jack@telecombts.com, or use the form at https://telecombts.com/contact-us/ with your board list and site software version, and we will help you match the right parts.
