Nokia FRGU and ARGA are both 6-pipe (6T6R) RF modules for Band 1 (2100 MHz), but they belong to different generations. FRGU (472956A) is a Flexi Multiradio RF module with 6 x 60 W output and OBSAI optical interfaces. ARGA (474800A) is an AirScale RF module with 6 x 80 W output, full-band 60 MHz bandwidth and CPRI interfaces. In short: FRGU fits existing Flexi and mixed Flexi/AirScale sites, while ARGA is the higher-power choice for AirScale sites where more output per carrier is needed. This guide compares the two and lists what to check when buying used units.
Quick Comparison: FRGU vs ARGA
The table below is based on Nokia module documentation and the Nokia Flexi Multiradio 10 / AirScale hardware roadmap. Where Nokia only gives a target value, it is marked as such.
| Item | Nokia FRGU | Nokia ARGA |
|---|---|---|
| Full name | Flexi RF Module 6TX 2100 (6 x 60 W) | AirScale RFM 6T6R B1 480W |
| Sales code | 472956A | 474800A |
| Product family | Flexi Multiradio 10 | AirScale |
| Band | Band 1: TX 2110–2170 MHz, RX 1920–1980 MHz | Band 1: TX 2110–2170 MHz, RX 1920–1980 MHz |
| TX / RX paths | 6T6R | 6T6R |
| Output power | 6 x 60 W (360 W total) | 6 x 80 W (480 W total) |
| Bandwidth | 60 MHz instantaneous, 40 MHz occupied | 60 MHz (full band), TX and RX |
| Optical interfaces | 3 x SFP, OBSAI, up to 6 Gbps | 3 x 9.8 Gbps CPRI |
| Radio technologies | WCDMA, FDD-LTE (NR in later releases) | WCDMA and LTE, concurrent mode |
| First software support (roadmap) | WCDMA 16, FDD-LTE 16, SRAN 16.2 | LTE 19, SRAN 19 |
| Antenna connectors | Not covered here | 4.3-10 |
| Size and weight | 115 x 420 x 400 mm (core), 24 kg | Nokia target: under 25 l and under 25 kg |
| Power supply | -48 V DC nominal | Check the module datasheet |
Key Differences Explained
1. Output power: 360 W vs 480 W
The most visible difference is power per pipe. Nokia FRGU delivers 60 W per pipe, while Nokia ARGA delivers 80 W per pipe. With a typical three-sector configuration using two pipes per sector (2T2R), ARGA gives each sector up to 160 W instead of 120 W. That extra headroom matters when an operator runs several WCDMA carriers and LTE in the same 2100 MHz band, or when it wants to keep coverage while adding a second technology on the same module.
2. Bandwidth and band coverage
Both modules cover Band 1 with 60 MHz instantaneous bandwidth. For FRGU, Nokia lists a 40 MHz occupied bandwidth, which limits how far apart carriers can be placed and how much total spectrum can be active at once. ARGA is specified with full-band occupied bandwidth on both TX and RX, so an operator with a wide Band 1 allocation can use more of it from a single module.
3. Fronthaul interface: OBSAI vs CPRI
This is the difference that most often decides compatibility. FRGU uses three OBSAI optical interfaces at up to 6 Gbps, the standard for Flexi Multiradio 10 radios. It works with the Flexi System Module FSMF and can also be reused on AirScale baseband with the appropriate capacity cards, which is a common step when a Flexi site is migrated. ARGA uses three 9.8 Gbps CPRI interfaces and is designed for the AirScale system module. Before ordering, confirm that your baseband hardware, optical SFPs and software release support the radio type you plan to connect.
For more on migrating a Flexi site and reusing its radios, see our guide Nokia FSMF to AirScale: Upgrade Path Explained.
4. Technologies and software
FRGU supports WCDMA and FDD-LTE, and later Nokia documentation also lists NR configurations on the module. ARGA supports WCDMA and LTE running at the same time on one module, with the split set by software. Nokia’s roadmap lists ARGA support from LTE 19 / SRAN 19, so older software loads will not recognise it. FRGU has been supported since release 16, which makes it easier to drop into a network running older software.
5. Physical installation
FRGU’s core module measures 115 x 420 x 400 mm and weighs 24 kg; front covers add width and depth. For ARGA, Nokia’s roadmap gives a target of under 25 litres and under 25 kg, and the module uses 4.3-10 antenna connectors. If you replace an older module with ARGA, check that you have the right jumper cables for the connector type and that the mounting kit fits your existing frame or pole bracket.
Which One Should You Choose?
- Choose FRGU if your site runs Flexi Multiradio 10 (FSMF), you need a like-for-like spare, or your software is older than the release that supports AirScale radios.
- Choose ARGA if the site runs AirScale baseband, you need more output power per carrier, or you plan to run WCDMA and LTE together on Band 1 with a wide spectrum allocation.
- Mixed networks: many operators keep FRGU on existing Flexi sites and deploy ARGA on new or upgraded AirScale sites. Keeping a small stock of both reduces downtime during a phased swap.
If you also need 1800 MHz capacity on AirScale, the sister module Nokia AREA (474198A) is the Band 3 equivalent of ARGA, with 6 x 80 W output.
What to Check When Buying Used FRGU or ARGA Modules
- Label and sales code: confirm 472956A for FRGU or 474800A for ARGA, and record the serial number. Our Nokia product codes guide explains how to read Nokia labels.
- Connectors: inspect RF and optical ports for corrosion, bent pins and damaged threads.
- Alarms: after commissioning, there should be no active hardware alarms on the module.
- RF performance: TX output on all six pipes and VSWR on each antenna port should be within specification.
- Optical link: use SFPs matched to the interface type (OBSAI for FRGU, CPRI for ARGA) and check that the link comes up at the expected rate.
- Software: confirm that your baseband software release supports the module before deployment.
For a step-by-step procedure, see Testing Used Nokia RF Modules: Pre-Deployment Checklist. You can browse all Nokia units in our Nokia product category.
FAQ
Can ARGA directly replace FRGU on a Flexi site?
Not as a simple swap. FRGU uses OBSAI interfaces for Flexi Multiradio 10, while ARGA uses CPRI and is designed for AirScale baseband. Replacing FRGU with ARGA is usually part of an AirScale upgrade, not a spare-part swap.
Do FRGU and ARGA cover the same frequencies?
Yes. Both cover Band 1 (2100 MHz): 2110–2170 MHz downlink and 1920–1980 MHz uplink. The differences are output power, occupied bandwidth, interface and software support.
Is ARGA better for running WCDMA and LTE together?
ARGA has more output power (80 W per pipe) and full-band occupied bandwidth, which gives more room to run WCDMA and LTE at the same time on Band 1. FRGU can also run both technologies, but with less power and a narrower occupied bandwidth.
What software release does ARGA need?
Nokia’s hardware roadmap lists ARGA support from LTE 19 and SRAN 19. Check the exact release notes for your network before deployment.
Buy Tested Nokia FRGU and ARGA Modules
Every unit we sell is functionally tested before shipment, and radio units such as FRGU and ARGA are also VSWR tested. All equipment comes with a 90-day warranty, and we ship worldwide in secure packaging. To check availability, contact us on WhatsApp at +86 187 3329 4669 or +86 139 3088 8705, email jack@telecombts.com, or use the form on our contact page.
We also buy surplus Huawei, Ericsson and Nokia equipment. Send us your list.
