Used Ericsson Baseband 6630 / 6631 baseband unit

Ericsson Baseband 6630 vs 6631: Key Differences

The Ericsson Baseband 6630 and Baseband 6631 are both 1U, 19-inch baseband units for Ericsson RAN sites, and Ericsson positions them at a similar capacity level. The short answer: the 6630 is the established multi-standard unit for GSM, WCDMA and LTE with 15 radio interface ports, while the 6631 is the later unit that adds native support for 5G New Radio (NR) and more flexible mixed-mode operation. If your site is LTE-only or 2G/3G/4G, the 6630 is usually enough; if you plan to run NR, the 6631 is the safer choice.

This guide compares the two units on hardware, interfaces, power and software support so operators, integrators and resellers can pick the right baseband for expansion, spares or swap projects.

Quick Comparison Table

FeatureBaseband 6630Baseband 6631
Form factor19-inch, 1U19-inch, 1U (44 x 483 x 383 mm)
DepthUnder 352 mm383 mm
Radio interface ports15 x SFP/SFP+ (CPRI)12 x SFP+ (CPRI)
Transport ports2 x 1/10G optical SFP/SFP+, 2 x 1G electrical RJ451G/10G optical SFP+ and 1G electrical RJ45
Synchronization1 x RJ45 sync port1 x RJ45 GNSS sync port
Power inputDual -48 V DCDual -48 V DC, redundant
Typical power consumption123 W130 W
Radio access technologiesGSM, WCDMA, LTE (hardware prepared for NR)GSM, WCDMA, LTE, NR
Mixed modeG+W, G+L, W+L, G+W+L (from SW 17.Q1)Up to four standards with flexible allocation
Product numberCheck the KDU number on the unit labelKDU 137 0071/11

Port counts and power figures are taken from published Ericsson product descriptions and datasheets. Always confirm the exact product number and revision on the unit label before ordering.

Baseband 6630: The Multi-Standard Workhorse

The Ericsson Baseband 6630 was introduced to replace the older DU-based architecture. According to Ericsson, a single 6630 matches the capacity of a Baseband 5216 while drawing over 50 W less than an equivalent Main Unit 6601 + Baseband 5216 combination.

Hardware and interfaces

  • 15 SFP/SFP+ ports for CPRI connections to radio units
  • 2 optical 1/10 Gbps SFP/SFP+ transport ports and 2 electrical 1 Gbps RJ45 ports
  • 1 RJ45 synchronization port, 1 LMT port and 8 external alarm inputs
  • Dual 48 V DC feeding and a field-replaceable fan unit
  • Mounts in a 19-inch rack or in the transmission compartment of Ericsson enclosures

Capacity

Ericsson’s product description lists typical LTE configurations (20 MHz, 2T2R FDD) of up to 3 sectors with 6 bands, or up to 6 sectors with 3 bands, and up to 3 sectors with 3 bands in 8T8R TDD. It supports GSM, WCDMA and LTE, including mixed-mode G+W, G+L, W+L and G+W+L from software release 17.Q1. The hardware was described as “prepared for NR and eCPRI”, but in the field the 6630 is mainly deployed for 2G, 3G and 4G.

Baseband 6631: Built with NR in Mind

The Ericsson Baseband 6631 (KDU 137 0071/11) handles switching, traffic management, timing, baseband processing and radio interfacing in the same 1U footprint. Ericsson’s datasheet describes it as having the same capacity as the 6630 but better flexibility for NR, with a maximum throughput of 5 Gbps downlink and 1 Gbps uplink.

Hardware and interfaces

  • 12 SFP+ radio interface (CPRI) ports
  • Ethernet transport on 1G/10G SFP+ and 1G RJ45 ports
  • 1 RJ45 GNSS receiver synchronization port, 1 RJ45 LMT port and RJ45 external alarm ports
  • Dual -48 V DC input with OR-ing redundancy
  • Dimensions 44 x 483 x 383 mm, about 7 kg, IP20, operating range 0 to 55 °C

Software and RAT support

The 6631 supports GSM, WCDMA, LTE and NR. In mixed mode it can run up to four standards with flexible allocation, which makes it a good fit for sites that keep legacy 2G/3G layers while adding LTE and NR on the same baseband.

Key Differences Explained

1. NR support

This is the main reason to choose one over the other. The 6631 lists NR as a supported standard and is described as more flexible for NR deployments. The 6630 is primarily a GSM/WCDMA/LTE unit. If NR is on your roadmap for the site, plan around the 6631 or a higher-capacity unit.

2. Radio port count

The 6630 offers 15 CPRI ports against 12 on the 6631. For sites with many radio units on one baseband, for example multi-band, multi-sector macro sites, count your CPRI links carefully before switching from a 6630 to a 6631.

3. Physical size and power

Both are 1U and 19 inches wide, but the 6631 is deeper (383 mm against under 352 mm), which matters in shallow cabinets. Typical power is close: 123 W for the 6630 and 130 W for the 6631. Both use dual -48 V DC feeds.

4. Software licensing and release

As with every Ericsson baseband, the features a unit can run depend on the software release and licenses on your network. Check that your OSS and software baseline support the hardware you add, and that the required capacity and feature licenses are in place before installation.

Which One Should You Choose?

  • Choose the 6630 for 2G/3G/4G sites, spares for an existing 6630 fleet, or sites that need the extra CPRI ports.
  • Choose the 6631 when the site will run NR, when you want up to four standards on one unit, or when you are standardising spares for newer software baselines.
  • Consider a higher-capacity unit such as the Baseband 6648 or the RAN Processor 6651 for heavy multi-band or high-capacity NR sites.

For a comparison with Ericsson’s higher-capacity unit, see our earlier article Ericsson Baseband 6630 vs 6648. You can browse all Ericsson baseband and radio units in our Ericsson product category.

What to Check When Buying a Used 6630 or 6631

  • Product number and revision: read the KDU number and R-state on the label and match it to your network plan.
  • Port condition: inspect SFP cages and RJ45 ports for damage or corrosion.
  • Fan and airflow: confirm the fan unit runs and the air paths are clean.
  • Alarm-free boot: the unit should start up and reach normal operation without hardware faults.
  • SFP modules: confirm whether optics are included and that they match your radio and transport links.

FAQ

Does the Baseband 6631 have more capacity than the 6630?

Ericsson’s datasheet describes the 6631 as having the same capacity as the 6630. The difference is better flexibility for NR and wider mixed-mode support, not raw capacity.

Can the 6630 run 5G NR?

The 6630 hardware was described as prepared for NR, but it is mainly used for GSM, WCDMA and LTE. For planned NR deployments, the 6631 or a higher-capacity unit is the more common choice. Confirm with your software release documentation.

Are the 6630 and 6631 the same size?

Both are 1U and 19 inches wide. The 6631 is deeper at 383 mm, while the 6630 is under 352 mm deep.

Can I replace a 6630 with a 6631 directly?

Physically they fit the same rack space if cabinet depth allows. Check that the 6631’s 12 CPRI ports cover your radio links, and that your software baseline, configuration and licenses support the new unit.

Get Ericsson Baseband Units from Telecombts

We supply used and refurbished Ericsson Baseband 6630, 6631, 6648 and RAN Processor 6651 units. Every unit is functionally tested before shipment, comes with a 90-day warranty, and is shipped worldwide in secure packaging. Contact us on WhatsApp at +86 187 3329 4669 or +86 139 3088 8705, email jack@telecombts.com, or use the form on our contact page.

We also buy surplus Huawei, Ericsson and Nokia equipment. Send us your list here.

Shopping Cart