The Huawei RRU5909 is a multimode, 2T2R remote radio unit with a maximum output of 2 x 60 W. In its 900 MHz version it covers the EGSM band (TX 925–960 MHz, RX 880–915 MHz) and can run GSM, UMTS, LTE FDD and NB-IoT on one unit, alone or in multimode combinations. That makes the Huawei RRU 5909-900 a common choice for low-band coverage layers, GSM/UMTS refarming to LTE, and like-for-like spares on existing Huawei 900 MHz sites. This article summarises the key specifications from Huawei’s RRU technical specifications (V100R015C10) and explains where the unit fits.
What is the RRU5909?
The RRU5909 belongs to Huawei’s RRU59xx generation of remote radio units used with the DBS3900 and DBS5900 distributed base stations. The radio is mounted near the antenna (on a pole, wall or tower) and connects to the baseband unit over CPRI fibre. Huawei documents the RRU5909 together with the RRU5309 and RRU5309w in the same hardware description, and the RRU5909 is produced in several frequency variants. The 900 MHz model is the one most often deployed for wide-area coverage and in-building penetration.
Because one RRU5909 can carry GSM, UMTS and LTE at the same time, operators use it to keep a legacy 2G or 3G layer running while moving part of the 900 MHz spectrum to LTE, without adding a second radio on the mast.
RRU5909 key specifications
The table below lists the main figures for the 900 MHz versions. Values are taken from Huawei’s RRU technical specifications; exact capabilities can vary with the software release on site.
| Item | RRU5909 (900 MHz) |
|---|---|
| TX/RX configuration | 2T2R |
| Frequency, 900 EGSM | RX 880–915 MHz / TX 925–960 MHz, IBW 35 MHz |
| Frequency, 900 PGSM | RX 890–915 MHz / TX 935–960 MHz, IBW 25 MHz |
| Supported RATs | GSM, UMTS, LTE FDD, LTE NB-IoT and multimode combinations (e.g. GU, GL, UL, GUL) |
| Maximum output power | 2 x 60 W |
| Capacity | GSM: 8 carriers; UMTS: 6 carriers without MIMO or 4 with MIMO; LTE FDD: 2 carriers (1.4/3/5/10/15/20 MHz); NB-IoT: 8 carriers |
| CPRI ports | 2, at 1.25, 2.5, 4.9 or 9.8 Gbit/s; star, chain or dual-star topology |
| Power supply | -48 V DC (range -36 V to -57 V DC) |
| Typical power consumption | 276 W (25°C, 50% load) |
| Dimensions (H x W x D) | 400 x 300 x 100 mm (12 L, without housing) |
| Weight | 14 kg (900 MHz, without housing) |
| Operating temperature | -40°C to +55°C without solar radiation; -40°C to +50°C with solar radiation |
| Ingress protection | IP65 |
Other RRU5909 variants in the same Huawei document cover 700 MHz, 1800 MHz and 2100 MHz with different IBW and mode support. When ordering, always check the band printed on the unit label, not only the model name.
Instantaneous bandwidth: why 35 MHz matters
The 900 EGSM variant has a 35 MHz instantaneous bandwidth, which covers the whole 880–915 / 925–960 MHz block. In practice this lets an operator place GSM and LTE carriers anywhere within its 900 MHz holding and change the split later through software, instead of being tied to a narrow sub-band.
CPRI and distance to the BBU
The two CPRI ports support star, chain and dual-star connections. According to Huawei, a GU configuration supports up to six cascading levels and 40 km to the BBU. For GL, UL or GUL configurations, the maximum distance is 40 km with UBBPe, UBBPg or UBBPd3–d6 baseband boards, but 20 km when NB-IoT or NR is included, or with older LBBPc/LBBPd1 boards.
Typical use cases
- Low-band coverage layer. 900 MHz propagates further and penetrates buildings better than mid-band, so the RRU5909 is often the coverage layer on rural and suburban macro sites.
- GSM/UMTS refarming to LTE. Multimode operation lets one radio carry GSM, UMTS and LTE together while traffic migrates from legacy networks.
- NB-IoT on existing 900 MHz sites. NB-IoT carriers can be added on the same unit for metering and IoT services.
- Spare and swap stock. Operators with installed RRU5909 fleets keep tested units as replacements so a failed radio can be swapped without reconfiguring the sector.
Compatibility with Huawei BBUs
The RRU5909 connects to Huawei baseband boards over CPRI. On current sites it is usually paired with a Huawei BBU 5900 fitted with e-series or g-series UBBP boards such as the Huawei UBBPe4; Huawei’s distance table above also lists these boards. It is also found on BBU3900 and BBU3910 sites. For details on which UBBP and UMPT boards fit which chassis, see our Huawei BBU5900 board compatibility guide.
As with any Huawei radio, physical connection is only half of the check. The site software release must support the RRU5909 in the mode combination you plan, and the CPRI rate of the baseband port must match the radio configuration.
RRU5909 vs mid-band 4T4R radios
The RRU5909 is a 2T2R low-band unit. Sites that need more capacity on 1800 or 2100 MHz typically add a 4T4R mid-band radio such as the Huawei RRU 5904-1800 alongside it. The two are complementary: the 900 MHz radio provides coverage, and the mid-band 4T4R radio provides capacity.
What to check when buying a used RRU5909
- Band and label. Confirm the frequency band and BOM code on the label match your network (900 EGSM vs 900 PGSM, or another band variant).
- Software support. Make sure your SRAN/eRAN release supports the RRU5909 in the RATs you need.
- Connectors and seals. Inspect the RF ports, CPRI optical ports, power connector and housing seals; the unit is rated IP65 only when the covers and seals are intact.
- Test results. Ask for functional and VSWR test results. Our Huawei RRU testing checklist explains what a proper test covers.
FAQ
Is the RRU5909 a 2T2R or 4T4R radio?
The RRU5909 is a 2T2R radio with a maximum output of 2 x 60 W.
Which technologies does the 900 MHz RRU5909 support?
GSM, UMTS, LTE FDD and LTE NB-IoT, either as a single mode or in multimode combinations such as GU, GL, UL and GUL, depending on the software release.
What power supply does the RRU5909 need?
It runs on -48 V DC, with an allowed input range of -36 V to -57 V DC.
Can the RRU5909 work with a BBU5900?
Yes. It connects to UBBP baseband boards in the BBU5900 over CPRI, provided the site software release supports the unit and the required mode combination.
Order a tested Huawei RRU5909
We supply used and refurbished Huawei RRU 5909-900 units together with matching BBUs and baseband boards. Browse the full range in our Huawei category. Every unit is functionally tested before shipment, and radio units such as RRUs are also VSWR tested. All equipment comes with a 90-day warranty, and we ship worldwide in secure packaging. Contact us on WhatsApp at +86 187 3329 4669 or +86 139 3088 8705, email jack@telecombts.com, or use the form at https://telecombts.com/contact-us/. We also buy surplus Huawei, Ericsson and Nokia equipment; see sell your equipment.
