Used Nokia Flexi FXED 1800 MHz RF module

Nokia FRMF vs FXED vs FRHF: Flexi RF Modules by Band

Nokia FRMF, FXED and FRHF are all 6-pipe (6T6R) Flexi Multiradio 10 RF modules, and the main difference between them is the frequency band. FRMF (472930A) covers Band 20 (800 MHz) with 6 x 60 W, FXED (472924A) covers Band 3 (1800 MHz) with 6 x 60 W, and FRHF (472849A) covers part of Band 7 (2600 MHz) with 6 x 40 W. Choosing between them is mostly a question of which spectrum your site uses, but output power, supported technologies and the FRHF sub-band also matter. This guide compares the three modules and explains what to check before you buy used units.

Quick Comparison: FRMF vs FXED vs FRHF

The values below come from Nokia Flexi Multiradio RF module documentation and the Nokia Flexi Multiradio 10 / AirScale hardware roadmap. Where a value is not confirmed in those sources, it is left out.

Item Nokia FRMF Nokia FXED Nokia FRHF
Nokia name Flexi RFM 6-pipe 800 360 W Flexi RFM 6-pipe 1800 360 W Flexi RF Module 6TX 2600
Sales code 472930A 472924A 472849A
3GPP band Band 20 (EU 800) Band 3 (1800) Band 7 (2600), sub-band
Downlink (TX) 791–821 MHz 1805–1880 MHz 2640–2690 MHz
Uplink (RX) 832–862 MHz 1710–1785 MHz 2520–2570 MHz
TX / RX paths 6T6R 6T6R 6T6R
Output power 6 x 60 W (360 W) 6 x 60 W (360 W) 6 x 40 W (240 W)
Radio technologies (roadmap) FDD-LTE GSM, FDD-LTE FDD-LTE
First software support (roadmap) FDD-LTE 16, SRAN 16.2 FDD-LTE 15, GSM 16, SRAN 16.2 LTE RL50, SRAN 16.2
AirScale counterpart (same band) ARMA (Band 20) AREA (Band 3, 6 x 80 W) ARHA (Band 7)

Key Differences Explained

1. Frequency band and coverage role

The band decides where each module is used in the network. Nokia FRMF works in the 800 MHz Band 20, the low-band LTE layer used across Europe and other regions for wide-area and indoor coverage. Low frequencies travel further and penetrate buildings better, so FRMF is often the coverage layer on rural and suburban sites.

Nokia FXED covers Band 3 (1800 MHz), one of the most widely used mid-band frequencies for both GSM and LTE. It is typically the main capacity layer on urban and suburban sites, and many operators refarm part of their GSM 1800 spectrum to LTE using the same hardware.

Nokia FRHF covers Band 7 (2600 MHz), a high-capacity LTE band used in dense areas where operators need extra bandwidth rather than range.

2. Output power: 60 W vs 40 W per pipe

FRMF and FXED both deliver 60 W per pipe, or 360 W in total. FRHF delivers 40 W per pipe, or 240 W in total. In a common three-sector layout with two pipes per sector (2T2R), that gives up to 120 W per sector for FRMF and FXED and up to 80 W per sector for FRHF. The lower power on FRHF reflects its role as a capacity layer: 2600 MHz cells are usually planned with a smaller footprint than 800 or 1800 MHz cells.

3. The FRHF sub-band

This is the point buyers most often miss. Band 7 as defined by 3GPP spans 2620–2690 MHz downlink and 2500–2570 MHz uplink. Nokia lists FRHF with a sub-band of 2640–2690 MHz downlink and 2520–2570 MHz uplink. If your licensed Band 7 block sits in the lower part of the band, check carefully that it falls inside the FRHF range before you order. A module that does not cover your carrier frequency cannot be fixed by software.

4. Technologies: GSM support on FXED

Of the three, FXED is the one with GSM in the Nokia roadmap (from GSM 16), alongside FDD-LTE. That makes it useful for single RAN sites that still carry GSM 1800 traffic next to LTE 1800. Nokia documentation lists a larger downlink instantaneous bandwidth for FXED in LTE and LTE/GSM sharing mode than in GSM-only mode, so check the configuration you plan to run against the module documentation. FRMF and FRHF are listed for LTE only, which matches how the 800 MHz and 2600 MHz bands are normally used.

5. Interfaces and system module

All three are Flexi Multiradio 10 RF modules. FXED has three SFP optical ports for the link to the system module, and the same Flexi optical interface approach applies to FRMF and FRHF. They are normally used with the Flexi System Module FSMF, and Flexi RF modules can also be reused on AirScale baseband when a site is migrated, provided the capacity cards, SFPs and software release support them. Our article Nokia FSMF to AirScale: Upgrade Path Explained covers that migration in more detail.

Where FRGU and the AirScale Modules Fit

FRMF, FXED and FRHF belong to the same Flexi 6-pipe family as FRGU, the Band 1 (2100 MHz) module with 6 x 60 W output. We compared FRGU with its AirScale successor in Nokia FRGU vs ARGA: 2100 MHz RF Module Differences.

For new or upgraded AirScale sites, Nokia’s roadmap lists AirScale RF modules for the same bands. The closest to FXED is Nokia AREA (474198A), a 6T6R Band 3 module with 6 x 80 W output and three 9.8 Gbps CPRI interfaces. AREA gives more power per pipe, but it is part of an AirScale design rather than a like-for-like Flexi spare.

Which Module Do You Need?

  • Choose FRMF if you need an 800 MHz (Band 20) LTE coverage layer or a spare for an existing Flexi 800 sector.
  • Choose FXED if your site runs GSM and/or LTE at 1800 MHz, or you are refarming GSM 1800 spectrum to LTE on Flexi hardware.
  • Choose FRHF if you run LTE at 2600 MHz and your carrier sits within 2640–2690 MHz downlink.
  • Multi-band sites: a typical Flexi site can combine modules, for example FRMF for coverage plus FXED for capacity, all connected to the same system module.

What to Check When Buying Used Flexi RF Modules

  • Sales code on the label: confirm 472930A (FRMF), 472924A (FXED) or 472849A (FRHF), and record the serial number. Our Nokia product codes guide explains how to read Nokia labels.
  • Frequency range: match the module band to your licence, especially the FRHF sub-band.
  • Connectors: check antenna ports, optical cages and the DC terminal for corrosion, bent pins or damaged threads.
  • Software release: confirm that the release running on your system module supports the module and the technology mode you plan to use.
  • RF performance: TX power on all six pipes and VSWR on each antenna port should be within specification, with no active hardware alarms after commissioning.

For a full procedure, see Testing Used Nokia RF Modules: Pre-Deployment Checklist, or browse all units in our Nokia product category.

FAQ

Can FXED replace FRMF or FRHF?

No. Each module is built for a specific band with its own filters. FXED works only in Band 3 (1800 MHz), FRMF only in Band 20 (800 MHz) and FRHF only in its Band 7 sub-band. Replace a module with the same type, or plan a band change with your RF design team.

Why does FRHF have lower output power?

FRHF is rated at 6 x 40 W compared with 6 x 60 W for FRMF and FXED. 2600 MHz is normally used as a capacity layer with smaller cells, so lower power per pipe is usually enough for its role.

Does FXED support GSM and LTE at the same time?

Nokia lists FXED for GSM and FDD-LTE, including LTE/GSM sharing mode, with support from GSM 16 and FDD-LTE 15 in the roadmap. Check your software release and license configuration before deployment.

Is there an AirScale version of these modules?

Yes. Nokia’s roadmap lists AirScale RF modules for the same bands, including AREA for Band 3, ARMA for Band 20 and ARHA for Band 7. They use CPRI and are intended for AirScale sites.

Buy Tested Nokia Flexi RF Modules

Every unit we sell is functionally tested before shipment, and radio units such as FRMF, FXED and FRHF are also VSWR tested. All equipment comes with a 90-day warranty, and we ship worldwide in secure packaging. To check availability, contact us on WhatsApp at +86 187 3329 4669 or +86 139 3088 8705, email jack@telecombts.com, or use the form on our contact page.

We also buy surplus Huawei, Ericsson and Nokia equipment. Send us your list.

Shopping Cart