Used Ericsson Radio 2219 B1 2100 MHz radio unit KRC 161 622/1

Ericsson Radio Band Variants: B1, B3, B7, B8, B20 Guide

Ericsson builds each radio model, such as the Radio 2217, Radio 2219 or Radio 4415, in several band variants, and the suffix after the model name (B1, B3, B7, B8, B20) tells you which 3GPP frequency band the unit transmits and receives on. A radio only works in the band its hardware filters are built for, so the band variant is the first thing to match when you buy a used unit: it must cover your licensed spectrum, connect to an antenna port that supports the same band, and be supported by your baseband software. This guide explains what each common band variant covers, which network layer it usually serves, and how to confirm the variant on a used radio before you order.

What the Band Suffix Means

In Ericsson’s naming, the model number describes the radio platform (for example, 2T2R or 4T4R, power class and ports), while the band suffix describes the frequency range. “Radio 2219 B3” and “Radio 2219 B8” share the same platform but are not interchangeable on site, because one is built for 1800 MHz and the other for 900 MHz. Some bands also come in sub-band variants, for example B3 and B3B, which cover only part of the band and can have a different instantaneous bandwidth (IBW). The exact variant is defined by the product number (KRC number) on the label, not only by the marketing name.

3GPP Frequency Ranges for Common Band Variants

The table below lists the standard 3GPP FDD frequency ranges for the bands most often seen on Ericsson radios in the used market. The same frequency ranges are reused for 5G NR as n1, n3, n7, n8 and n20.

Variant Common name Uplink (MHz) Downlink (MHz) Typical network role
B1 2100 MHz (IMT) 1920–1980 2110–2170 WCDMA legacy, LTE/NR capacity layer
B3 1800 MHz (DCS) 1710–1785 1805–1880 Main LTE layer in many markets, GSM 1800, NR via refarming
B7 2600 MHz (IMT-E) 2500–2570 2620–2690 Urban LTE capacity layer
B8 900 MHz (E-GSM) 880–915 925–960 Coverage layer: GSM, WCDMA, LTE, NR refarming
B20 800 MHz (EU Digital Dividend) 832–862 791–821 LTE coverage and indoor penetration

Note that Band 20 uses reversed duplex: the downlink sits below the uplink. This is normal for the band and does not indicate a labelling error.

Matching the Band Variant to Your Network Layer

Coverage layers: B8 and B20

Sub-1 GHz bands travel further and penetrate buildings better, so operators use them for rural coverage and deep indoor service. Band 8 is common across Europe, Africa, the Middle East and Asia, often carrying GSM alongside LTE or NR. Band 20 is mainly a European LTE band. A typical buyer for these variants is an operator expanding rural sites or replacing failed units on an existing coverage layer. Our stock includes the Ericsson Radio 2219 B8 and the Ericsson Radio 2217 B20.

Mid-band workhorses: B3 and B1

Band 3 (1800 MHz) is the most widely deployed LTE band in many regions, and Band 1 (2100 MHz) is moving from WCDMA to LTE and NR as 3G is switched off. On these layers, buyers often choose between 2T2R radios (Radio 2219) for like-for-like replacement and 4T4R radios (Radio 4415, 4428, 4429) for more capacity per sector. Relevant units include the Ericsson Radio 2219 B3, the Ericsson Radio 4415 B3 and the Ericsson Radio 4415 B1.

Capacity layer: B7

Band 7 (2600 MHz) offers wide FDD blocks in many countries and is used to add capacity at busy urban sites. Its shorter range makes it a poor choice for coverage, but it is valuable where traffic is concentrated. Ericsson radios in this band include the Radio 2217 B7 and Radio 4415 B7.

Band Variants by Model in Our Range

Model Configuration Band variants we list
Radio 2217 2T2R B7, B20
Radio 2219 2T2R B1, B3, B8
Radio 4415 4T4R B1, B3, B7
Radio 4428 4T4R B3
Radio 4429 4T4R B3

For a detailed comparison of the two 2T2R platforms, see our article on Ericsson Radio 2217 vs 2219. The full range is in our Ericsson category.

How to Confirm the Band Variant on a Used Radio

  1. Read the label, not the listing title. The product label shows the KRC product number, revision (R-state) and usually the frequency band. Ask the seller for a clear photo of the full label. Our guide to Ericsson radio KRC numbers explains how to read it.
  2. Check for sub-band variants. If your licensed block sits at the edge of a band, confirm whether the unit is a full-band or sub-band variant (for example B3 vs B3B) and that its IBW covers your carrier spread.
  3. Match the antenna. The antenna port connected to the radio must support the same band. On multiband antennas, verify which port maps to which frequency range.
  4. Confirm baseband and software support. Your baseband (for example Baseband 6630 or 6648) must run a software release that supports the radio type and band, with the right licences for carriers and output power. See our radio and baseband compatibility guide.
  5. Plan for mixed vendors carefully. An Ericsson radio connects to an Ericsson baseband over Ericsson’s CPRI implementation. Do not plan to connect it to another vendor’s baseband.
  6. Inspect connectors. Check the RF ports, data (fronthaul) ports and DC power connector for corrosion or damage, especially on units removed from coastal sites.

Common Mistakes When Ordering by Band

  • Ordering by frequency name only. “1800 MHz radio” can mean a full B3 unit or a sub-band variant. Always quote the product number.
  • Mixing up 800 and 850 MHz. Band 20 (800 MHz EU) and Band 5 (850 MHz) are different bands and radios are not interchangeable between them.
  • Assuming 2T2R and 4T4R units swap directly. Moving from a 2219 to a 4415 on the same band changes the number of antenna branches, cabling and configuration. Our Radio 2219 to 4415 upgrade guide covers the details.
  • Ignoring NR plans. If you intend to run NR or spectrum sharing on the band later, confirm that the variant and your baseband software support it.

FAQ

Can I retune an Ericsson B3 radio to work on Band 1?

No. The band is set by the radio’s hardware filters and power amplifiers. A B3 unit only operates in the 1800 MHz band, so you need a B1 variant for 2100 MHz.

Are B8 radios suitable for GSM and LTE at the same time?

Many Ericsson radios support mixed-mode operation, but support depends on the specific model, band variant, baseband software and licences. Check the radio’s capability data for your exact product number.

What is the difference between B3 and B3B?

B3B is a sub-band variant that covers only part of Band 3, and its IBW can differ from the full-band B3 unit. Check that the sub-band covers your licensed frequencies before ordering.

Which band should I use for rural coverage?

Sub-1 GHz bands such as B8 (900 MHz) and B20 (800 MHz) give the widest coverage per site. Mid and high bands such as B3, B1 and B7 are mainly used for capacity.

Buy Tested Ericsson Radio Units by Band

Every unit we sell is functionally tested and VSWR tested before shipment, comes with a 90-day warranty, and is shipped worldwide in secure packaging. Send us the model, band variant and quantity you need via WhatsApp +86 187 3329 4669 / +86 139 3088 8705, email jack@telecombts.com, or the form on our contact page.

We also buy surplus Huawei, Ericsson and Nokia equipment. Sell your equipment to us.

Shopping Cart