The Huawei RRU5509t is a tri-band remote radio unit that covers the 700 MHz, 800 MHz and 900 MHz bands in a single 2T4R box. It is built for operators who want to run their low-band layers (LTE coverage at 700/800 MHz plus GSM, UMTS or LTE refarming at 900 MHz) from one radio instead of two or three. This guide summarises the key specifications from Huawei’s RRU technical specifications (V100R015C10), the modes the unit supports and where it fits in a network.
What is the Huawei RRU5509t?
The RRU5509t belongs to Huawei’s RRU5000 series of multi-band radios. The “t” models are tri-band units: the RRU5509t can work in any one of its three bands, in any two of them, or in all three at the same time. Each band has its own instantaneous bandwidth, and the unit connects to the baseband over CPRI, so it is deployed with a Huawei BBU such as the BBU5900 or, depending on software release and board configuration, the BBU3910.
The main advantage is consolidation. On sites where 800 MHz LTE and 900 MHz GSM/UMTS were originally served by separate radios, one RRU5509t can replace them, reducing tower load, power cabling and the number of units to maintain. The 700 MHz band (band 28 range) can be added on the same hardware when the operator holds that spectrum.
RRU5509t key specifications
The figures below are taken from Huawei’s RRU technical specifications document. Values can differ between software versions, so always confirm against the documentation for the release running on your network.
| Parameter | RRU5509t |
|---|---|
| Frequency bands | 700 MHz, 800 MHz, 900 MHz (tri-band) |
| 700 MHz | RX 703–733 MHz / TX 758–788 MHz, IBW 30 MHz |
| 800 MHz | RX 832–862 MHz / TX 791–821 MHz, IBW 30 MHz |
| 900 MHz | RX 880–915 MHz / TX 925–960 MHz, IBW 35 MHz |
| RF channels | 2T4R, four RF ports (A–D) |
| Maximum output power | 2 x 140 W; 2 x 80 W in single-band operation or 700+800 MHz combination |
| CPRI | 2 ports, 1.25 / 2.5 / 4.9 / 9.8 Gbit/s; star, chain or dual-star topology |
| Power supply | -48 V DC (-36 V to -57 V DC) |
| Dimensions | 480 x 356 x 140 mm (24 L, without housing) |
| Weight | 25 kg (without housing) |
| Typical power consumption | 560 W (700+800+900 MHz) |
| Operating temperature | -40°C to +55°C without solar radiation; -40°C to +50°C with solar radiation |
| Ingress protection | IP65 |
| Antenna support | TMA supported; RET via AISG 2.0 |
Supported modes per band
Mode support depends on the band, which is important when planning refarming:
- 700 MHz and 800 MHz: LTE FDD, LTE + NB-IoT (LM), and LTE + NR supplementary uplink (LN SUL).
- 900 MHz: GSM, UMTS and LTE FDD, plus multimode combinations such as GU, GL, UL and GUL, with NB-IoT combinations available as well.
In practice this means the 900 MHz path is the flexible one: it can keep a legacy GSM layer alive while LTE takes over part of the spectrum, while the 700 and 800 MHz paths are LTE-focused.
Carrier capacity
According to the specifications, the RRU5509t supports up to 8 GSM carriers, 6 UMTS carriers without MIMO (4 with MIMO), and 2 LTE FDD carriers per band (4 across two bands, 6 across three) with 5, 10, 15 or 20 MHz carrier bandwidth. NB-IoT is supported with up to 8 carriers per band, and one NR SUL carrier is supported.
Typical use cases
Low-band consolidation on macro sites
The most common use is replacing separate 800 MHz and 900 MHz radios with one unit. This is typical in European-style band plans where band 20 (800 MHz) LTE and band 8 (900 MHz) GSM/UMTS/LTE share the same sector antennas.
Adding 700 MHz coverage
Operators that acquired 700 MHz spectrum can light it up on the same radio without adding another unit on the mast, provided the antenna and feeder system support the band.
GSM and UMTS refarming
Because the 900 MHz band supports GSM, UMTS and LTE together, the RRU5509t suits networks that are gradually shrinking 2G/3G and moving 900 MHz spectrum to LTE.
Deployment notes
- PIM considerations: Huawei notes that in 2T4R mode, third-order intermodulation (PIM3) of the transmit signals may fall into receive bands. In that case the affected bands should run 2T2R on a four-port antenna with TX and RX on different ports. Plan the antenna and port mapping before installation.
- Power budget: Output power drops to 2 x 80 W in single-band or 700+800 MHz operation, so check the power configuration against your link budget.
- Baseband and software: Confirm that your BBU, baseband boards and software release support the RRU5509t and the mode combination you plan to use. Our BBU5900 board compatibility guide covers the UBBP and UMPT side.
- Weight and mounting: At 25 kg without housing, allow for the mounting kit and pole or wall capacity.
RRU5509t vs single-band 900 MHz radios
If a site only needs 900 MHz, a single-band radio such as the Huawei RRU5909 900 MHz may be the simpler choice (see our RRU5909 specs article). The RRU5509t makes sense when two or three sub-1 GHz bands must run on the same sector and tower space or power is limited.
What to check when buying a used RRU5509t
- BOM code and label details match the version you need.
- All four RF ports, CPRI ports and the power connector are free of damage and corrosion.
- Test results cover output power and VSWR on each band you plan to use.
- No active alarms after power-up and CPRI link establishment with a BBU.
More Huawei radio and baseband units are listed in our Huawei product category.
FAQ
Which bands does the Huawei RRU5509t support?
It supports 700 MHz, 800 MHz and 900 MHz, and can operate in any one, two or all three bands simultaneously.
Is the RRU5509t 2T4R or 4T4R?
It is a 2T4R radio with four RF ports. In some PIM-sensitive cases, Huawei recommends running affected bands as 2T2R.
Can the RRU5509t run GSM?
Yes, on the 900 MHz band. The 700 and 800 MHz bands are used for LTE FDD, NB-IoT and NR SUL.
What power supply does it need?
-48 V DC, with an input range of -36 V to -57 V DC.
Get a quote for the Huawei RRU5509t
Every unit we supply is functionally tested and VSWR tested before shipment, comes with a 90-day warranty, and is shipped worldwide in secure packaging. Contact us on WhatsApp +86 187 3329 4669 / +86 139 3088 8705, email jack@telecombts.com, or use the form at https://telecombts.com/contact-us/.
We also buy surplus Huawei, Ericsson and Nokia equipment — send us your list.
